Short answer
A hatch fills a closed area with parallel lines to show a material or a cut element. In ARCTE CAD you select a closed boundary and type `HATCH 150 45` (150 mm spacing, 45°), or click inside the boundary to create a hatch with `HATCHAT`. The hatch is linked to its boundary: it updates when the boundary changes and warns you if the boundary opens.
Two methods
| Command | How | When |
|---|---|---|
HATCH (Turkish alias: tarama) | Select the closed boundary (closed polyline, circle, ellipse or closed chain of lines/arcs) and give the spacing and angle: HATCH 150 45 | If the boundary is a single closed object |
HATCHAT | Give a point inside the area: HATCHAT 2000,1500 150 45 (45° if no angle is entered) | If the boundary consists of several lines |
Nested closed boundaries (for example an opening in a floor slab) are kept as islands and are not hatched.
Step by step
01Choose the hatch layer
Keep hatches on a separate HATCH layer; give it a fine lineweight (0.13–0.18 mm).
02Close the boundary
Make sure the boundary really is closed. You can join the ends into a single polyline with
JOINor close an open polyline withPEDIT CLOSE.03Create the hatch
Select the boundary and type
HATCH 150 45, or click inside the area withHATCHAT.04Send it to the back
So that the hatch does not cover walls and text, use
DRAWORDER BACK.05Check in the preview
If the spacing looks too dense on the sheet, increase it. The spacing is chosen according to the output scale: on a 1:50 sheet, a 100 mm spacing is 2 mm on paper.
Suggestions for showing materials
In ARCTE CAD, a hatch consists of parallel lines in a single direction; there is no library of predefined patterns (such as ANSI) and no solid fill. You can achieve common representations as follows:
| Representation | How |
|---|---|
| Cut wall (general) | Dense single-direction hatch at 45° |
| Reinforced concrete | Two hatches at 45° and 135° on the same boundary (cross-hatch) |
| Floor finish (e.g. ceramic tiles) | Two hatches at 0° and 90°; spacing equal to the tile size (e.g. 600 mm) |
| Parquet | Single direction, spacing equal to the board width (e.g. 150 mm) |
These are common drawing conventions; if your practice or the authority has a representation standard, follow it.
Common hatch messages
| Message | Cause | Solution |
|---|---|---|
| "No closed boundary found at the clicked point" | The boundary has an open end or a gap; gaps are not closed automatically | Close the ends with EXTEND, TRIM or JOIN |
| "Select a closed chain of lines/arcs, a polyline, a circle or an ellipse" | The object selected for HATCH is not closed | Close the boundary or use HATCHAT |
| "Area boundary does not close or intersects itself" | The boundary crosses over itself | Fix the intersecting edges |
| "Associated area boundary has opened" | The boundary the hatch is linked to was opened later | Join the ends or remove the hatch |
| "Hatch spacing must be at least 0.1 mm" | The spacing is too small | Give a larger spacing |
| "For an inner boundary search, select at most 5,000 lines/arcs in the region" | Searching in a very large region | Zoom in on the region to be hatched and select fewer objects |
Frequently asked questions
The boundary is not closed. ARCTE CAD does not close gaps automatically; close the open ends with the extend, trim or join commands and try again.
Apply two hatches to the same boundary, one at 45° and the other at 135°.
Yes. The hatch is linked to its boundary and updates when the boundary changes. A warning is given if the boundary opens or the number of edges changes; if the boundary is deleted, the hatch remains as independent geometry.
No. A hatch consists of parallel lines; you can achieve a dense appearance with close spacing and cross-hatching.