Short answer
Scale is the ratio of a length on paper to the real length: at 1:100, 1 cm on paper is 1 m in reality; at 1:50 it is 50 cm. In CAD, the drawing is always drawn at real size (1:1, in millimetres); the scale is chosen only when producing the sheet output. In ARCTE CAD you choose the scale in page setup, from preset values between 1:1 and 1:500 or as a custom value.
What is scale and how do you read it?
Scale is written as "1/n" or "1:n" and says that 1 unit on paper is n units in reality. The larger the denominator, the smaller the drawing and the less detail is shown: 1:500 suits a site plan, 1:5 a joinery detail.
| Scale | 1 cm on paper | 1 m in reality on paper | Typical use |
|---|---|---|---|
| 1:500 | 5 m | 2 mm | Site and layout plans |
| 1:200 | 2 m | 5 mm | Site plan, floor plans of large buildings, early studies |
| 1:100 | 1 m | 1 cm | Preliminary design plans, sections and elevations |
| 1:50 | 50 cm | 2 cm | Construction drawing plans, sections and elevations |
| 1:20 | 20 cm | 5 cm | Enlarged plans such as wet rooms, stairs and kitchens |
| 1:10, 1:5, 1:1 | 10 cm, 5 cm, 1 cm | 10 cm, 20 cm, 1 m | System and joinery details |
The uses in the table reflect common practice. The scale and sheet layout required for a building permit or tender may vary according to the specification of the relevant authority (municipality, public body); check before submission.
Scale in CAD: the drawing at 1:1, the scale on the sheet
In hand drawing, the scale is chosen at the outset; in CAD it is the other way round. Walls, openings and furniture are drawn at their real dimensions (in millimetres in ARCTE CAD). That way you can produce a 1:100 preliminary sheet and a 1:50 construction sheet from the same drawing, and measure distances and areas directly.
01Draw at real size
For a 5 m wall, type
WALL 0,0 5000,0 200: length 5000 mm, thickness 200 mm. Check the unit withUNITS.02Switch to the layout
Prepare your sheet on the Layout tab below the drawing area.
03Choose the scale
Use
PAGESETUPto set the plot area to Layout and the scale to 1:50 or 1:100. "Fit to paper" gives unscaled output; do not use it for a scaled sheet.04Check that it fits the paper
Use
PLOTPREVIEWto see that the drawing fits the selected paper (A4–A0) at this scale; if it does not, use a larger paper or a smaller scale.
Which scale fits which paper?
To work out the paper you need, divide the real size of the drawing by the scale denominator. At 1:100, a 24 m × 15 m floor plan takes up 24 cm × 15 cm on paper and fits on A4 (29.7 × 21 cm); at 1:50 the same plan becomes 48 cm × 30 cm and does not fit on A3 (42 × 29.7 cm), so A2 (59.4 × 42 cm) is needed.
| Paper | Size (mm) | Area that fits at 1:100 | Area that fits at 1:50 |
|---|---|---|---|
| A4 | 297 × 210 | 29.7 m × 21 m | 14.8 m × 10.5 m |
| A3 | 420 × 297 | 42 m × 29.7 m | 21 m × 14.8 m |
| A2 | 594 × 420 | 59.4 m × 42 m | 29.7 m × 21 m |
| A1 | 841 × 594 | 84.1 m × 59.4 m | 42 m × 29.7 m |
| A0 | 1189 × 841 | 118.9 m × 84.1 m | 59.4 m × 42 m |
Part of these areas is taken up by margins, the title block and dimension lines; in practice, leave a few centimetres of allowance in each direction.
Text height and lineweight
Because the drawing is 1:1, text is also written at real size and shrinks with the scale in the output. Multiply the text height you want on paper by the scale denominator: text that should appear 2.5 mm high on a 1:100 sheet must be 250 mm in the drawing, and 125 mm for a 1:50 sheet. Example: TEXT 100,100 250 Lounge.
Lineweights, on the other hand, are millimetres on paper and are not affected by scale. Give layers values such as 0.18–0.25 mm (fine), 0.35 mm (medium) and 0.50–0.70 mm (heavy, e.g. cut walls) and check them in print preview.
Common scale mistakes
- Leaving the output scale on "Fit to paper": the sheet is not to scale and cannot be measured with a scale rule.
- Opening a DWG with the wrong unit: taking a plan drawn in metres for millimetres makes areas a million times smaller. Check a known dimension with
DIST. - Preparing a sheet by scaling the drawing:
SCALEchanges the real size of the geometry; the scale must be chosen in the sheet settings. - Not stating the scale on the sheet: write the scale in the title block and below each drawing.
Frequently asked questions
It means that 1 cm on paper is 100 cm (1 m) in reality. On a 1:100 plan, a 5 m wall appears 5 cm long on paper.
A 1:50 drawing is larger and more detailed: the same wall appears twice as long on paper at 1:50 as at 1:100.
Always draw at 1:1, i.e. real size. The scale is chosen only in page setup when producing the sheet output.
Open page setup in the layout, set the plot area to Layout and the scale to 1:50 or 1:100, check in print preview and create a vector PDF with the PDF export command.