Short answer
A room schedule is a project document that collects, in one table, the number, name and net area of every space (room) in a project, usually together with its floor, wall and ceiling finishes. It is used on construction drawings and in preparing quantity take-offs and cost estimates. In ARCTE CAD you measure the net area of each room from the plan, write the room name and m² value on the plan, and build the schedule on the same sheet with the table command.
What is a room schedule for?
A room schedule identifies the spaces you see on the plan one by one: it shows how much area each space has and which material is used on each surface. The site team reads from this schedule what is to be done in each room, and quantity take-offs and cost estimates usually start from it too.
The schedule is also a check on consistency between sheets: the room labels and area values on the plan and the rows in the table must match.
The content and format of a room schedule vary by authority, client and project stage. Use the template required by the authority or client you are submitting to.
What information does a room schedule contain?
The columns below are the most common. At the preliminary design stage, number, name and area may be enough; at the construction drawing stage, finish information is added.
| Column | What to enter | Example |
|---|---|---|
| Room no. | The number on the plan; usually starts with the floor code | G-01 |
| Room name | The use of the space | Living room |
| Net area (m²) | The area between the inner faces of the walls | 32.64 |
| Floor | Final floor finish | Laminate flooring |
| Wall | Wall surface finish | Satin paint |
| Ceiling | Ceiling finish | Paint on plaster |
| Skirting | Material and height | Timber, 8 cm |
| Note | Special conditions such as wet rooms or insulation | Waterproofing required |
The difference between net area and gross area
Net area is the usable area between the inner faces of the walls enclosing a room. Gross area is measured from the outer lines, walls included. A room schedule usually gives the net area for each space; floor or building totals are given separately as gross area.
| Net area | Gross area | |
|---|---|---|
| Measured from? | The inner faces of the walls | The outer faces of the walls |
| Walls included? | No | Yes |
| In the room schedule | In each room's row | Usually in the floor or building total |
Which areas count in zoning and floor area ratio calculations is set by the applicable regulations. This guide does not replace that calculation.
Preparing a room schedule step by step
01Name and number the rooms
Give each space a name and a number starting with the floor code (e.g. G-01, G-02 for the ground floor). Distinguish spaces with the same name by their number.
02Measure the net areas from the plan
Rather than calculating areas by hand, measure them from the closed boundaries in the drawing. Make sure the boundaries really are closed and that no gaps remain at the wall junctions.
03Add the finish information
Enter the floor, wall, ceiling and skirting information using the same names as the materials list or specification; do not give the same material two different names.
04Place the table on the sheet
Put the schedule next to the plan or on a separate sheet. State the column headings and units (m², cm) clearly.
05Update it as the plan changes
When a wall moves, the areas change too. Before submission, do a final check by comparing the sum of the room areas with the floor area.
Room schedules with ARCTE CAD
ARCTE CAD measures the net area of rooms from closed boundaries and writes the name and m² value on the plan. Areas are linked to their boundaries; when the drawing changes, it shows which areas need updating.
01Draw the walls or import them from DWG
Draw the walls with the
WALLcommand or open your existing DWG plan. TheAUDITcommand checks L, T and X junctions; a junction left open breaks the room boundary.02Measure the room area
Select the surrounding walls and type
ROOM Lounge, or useROOMAT 2000,1500 Loungewith a point inside the closed area. The room name and net area are written on the plan.03Keep unnecessary lines out of the calculation
Use the
ROOMLAYERScommand to make sure furniture layout, grid line and title block layers are not counted as room boundaries. For plans from DWG, choose the source unit correctly; a wrong unit makes areas appear 100 times off.04Build the schedule as a table
The
TABLEcommand builds a table from lines and editable text; you separate columns with | and rows with ;. Example:TABLE 0,0 3 4 1200 450 "No|Room|Net area (m²)|Floor;G-01|Lounge|32.64|Laminate". You can change cells later withTABLECELL.05Check the total and that areas are up to date
AREAgives the total area of the selected closed objects (overlapping areas are not subtracted).RELATIONSlists the dimensions and areas that need updating; while an out-of-date area exists, PDF and DXF output is stopped, so no sheet goes out with a wrong area.
ARCTE CAD does not currently generate the room schedule from the plan as an automatic table: it measures and labels the areas, and you build the table. If the plan changes, update the values in the table too.
Common mistakes
- Boundary not closed: a small gap at a wall junction means the area cannot be found or merges with the neighbouring space.
- Furniture lines counted as boundaries: furniture, grid line or title block lines reduce the area; keep these layers out of the calculation.
- Wrong unit: if the unit is chosen wrongly for a plan from DWG, areas come out 100 or 1,000,000 times off. Check by measuring a known distance.
- Mixing up net and gross area: state clearly that room rows use net area and the floor total uses gross area.
- Out-of-date table: a table that is not updated after the plan changes is the most common inconsistency.
Frequently asked questions
The most common method is a sequence number starting with the floor code: G-01, G-02 for the ground floor; 1-01, 1-02 for the first floor, and so on. If the authority you are submitting to requires a particular system, use that.
Each room's row usually gives the net area, i.e. the area between the inner faces of the walls. The gross area can be given separately in the floor or building total.
No. ARCTE CAD measures the net area of rooms and writes the name and m² value on the plan; you build the schedule with the TABLE command. You are warned about out-of-date areas before output.
Most likely the source unit was chosen wrongly. Choose the unit (mm, cm, m) correctly when opening the DWG and verify it by measuring a known distance with the DIST command.