Short answer
The ARCTE CAD command line recognises Turkish command names (such as duvar, kapı, buda, ekrana sığdır) together with English command names and their aliases (such as LINE / L, TRIM / TR). You type the command and press Enter; the F1 key opens the command reference. The reference below is taken from the app's own command catalogue.
How do you use the command line?
- Type the command name in Turkish or English and press Enter:
duvar,WALLand its aliasWrun the same command. - You can type parameters on the same line, separated by spaces:
duvar 0,0 5000,0 200(start, end and thickness in mm). - Coordinates are in millimetres in the form
X,Y; for a value relative to the last point, prefix it with @:MOVE @0,200. - Use a full stop as the decimal separator:
LINEWEIGHT 0.35. - You can type without Turkish characters:
cizgiandçizgiare the same command. - F1 opens the command reference;
komut ara(COMMANDS) opens the searchable command catalogue.
Keyboard shortcuts
| Key | Action |
|---|---|
| F1 | Command reference |
| F3 | Object snap on/off |
| F7 | Grid on/off |
| F8 | Ortho |
| F9 | Snap to grid |
| F10 | Polar tracking (15° increments) |
| F11 | Object tracking (alignment) |
| F12 | Dynamic input |
| Ctrl + Z | Undo |
| Ctrl + Y | Redo |
Drawing commands
| Turkish | Command | Alias | What it does | Example |
|---|---|---|---|---|
| çizgi | LINE | L | Line between two points | LINE 0,0 4000,0 |
| çoklu çizgi | PLINE | PL | Polyline; close with C | PLINE 0,0 2000,0 2000,1500 C |
| dikdörtgen | RECTANG | REC | Rectangle from two opposite corners | RECTANG 0,0 4000,3000 |
| çember, daire | CIRCLE | C | Centre and radius | CIRCLE 2000,1500 500 |
| yay | ARC | A | Centre, radius, start/end angle in degrees; anticlockwise | ARC 0,0 1000 0 90 |
| elips | ELLIPSE | EL | Centre, two radii and an optional rotation angle | ELLIPSE 0,0 1000 500 30 |
| çokgen | POLYGON | POL | Regular polygon from the centre and circumscribed circle radius | POLYGON 6 0,0 1000 |
| tarama | HATCH | H | Hatch the selected closed boundary at the given spacing (mm) and angle (degrees) | HATCH 150 45 |
| — | HATCHAT | — | Associative hatch inside a closed line/arc boundary | HATCHAT X,Y 150 45 |
Walls, doors, windows and rooms
Architectural objects are linked to each other: doors and windows sit on the wall, and the room area is calculated from the walls around it.
| Turkish | Command | Alias | What it does | Example |
|---|---|---|---|---|
| — | WALLTHICKNESS | — | Thickness for new walls; preset sizes from the drop-down arrow or a custom value in cm | WALLTHICKNESS 15cm |
| duvar | WALL | W | Centreline, thickness and an optional label | WALL 0,0 5000,0 200 lounge north |
| pencere | WINDOW | WIN | Type PENCERE, then click the window centre on an existing wall. ID form: WINDOW wallId distance width | PENCERE 1400 |
| kapı | DOOR | DR | Type KAPI, then click the door centre on an existing wall. ID form: DOOR wallId distance width | KAPI 900 |
| — | ROOMAT | — | Net area of the closed room containing the point | ROOMAT 2000,1500 Lounge |
| duvar denetimi, denetle | AUDIT | — | Check wall geometry and L/T/X junctions | AUDIT |
| — | RELATIONS | — | Show dimensions and areas that need reviewing | RELATIONS |
| — | RELINK | — | Relink the selected room/hatch boundary to the clicked closed region; relink a dimension to its endpoints | RELINK 2000,1500 |
| mahal, oda | ROOM | RM | Dynamic net area from the selected surrounding walls | ROOM Lounge |
| — | WALLFROM | — | Creates walls from the selected straight lines and keeps the sources. Thickness and CENTER/LEFT/RIGHT reference | WALLFROM 200 CENTER |
| — | WALLPAIR | — | Creates a wall from two aligned LINEs or the offset faces of matching closed, straight-edged PLINEs; keeps the sources | WALLPAIR |
| — | DWGNATIVE | — | Creates native walls, doors and windows from the geometry of a DWG-based drawing | DWGNATIVE |
| — | ROOMLAYERS | — | Set the source role of each layer for new room searches | ROOMLAYERS |
Dimensions, text and tables
| Turkish | Command | Alias | What it does | Example |
|---|---|---|---|---|
| tablo | TABLE | TB | Grouped 2D table built from lines and editable text; columns separated by |, rows by ; | TABLE 0,0 3 4 1200 450 "Title|Qty|Unit|Note;Wall|1|m²|" |
| — | TABLECELL | TBC | Change a row/column cell of the selected table; empty text clears the cell | TABLECELL 2 1 Wall |
| açıklama oku | MLEADER | MLD | Grouped 2D leader from the arrowhead, landing, text point and height | MLEADER 0,0 800,700 1800,700 180 Wall note |
| — | MLEADERADD | MLA | Attach a new arrow to the shared text of the selected leader | MLEADERADD 0,0 800,700 |
| — | MLEADEREDIT | MLE | Change the text and text/arrow height of the selected leader | MLEADEREDIT 180 Wall note |
| yazı | TEXT | T | Position, text height in mm and the text | TEXT 100,100 180 Lounge |
| — | MTEXT | MT | Multiline text from two corners; in numeric form: point, width, text height and quoted text | MTEXT 100,100 2500 180 "Lounge note" |
| doğrusal ölçü, ölçü | DIMLINEAR | DLI | Horizontal/vertical dimension; two endpoints + normal offset + H/V (optional); associated with the endpoints | DIMLINEAR 0,0 3000,4000 4500 H |
| hizalı ölçü | DIMALIGNED | DAL | Aligned true distance; two endpoints + perpendicular offset; associated with the endpoints | DIMALIGNED 0,0 3000,4000 500 |
| mesafe | DIST | DI | Distance between two points | DIST 0,0 3000,4000 |
| alan | AREA | AA | Total area of the selected closed objects; overlaps are not subtracted | AREA |
Editing commands
| Turkish | Command | Alias | What it does | Example |
|---|---|---|---|---|
| noktadan böl | BREAKATPOINT | BRP | Break the selected LINE, ARC or open PLINE; walls are not broken | BREAKATPOINT 250,0 |
| uzunluk | LENGTHEN | LEN | Change the total length of a line while keeping its start point | LENGTHEN 2000 |
| esnet | STRETCH | S | Move the LINE/PLINE/wall endpoints inside the window | STRETCH 0,0 2000,2000 @500,0 |
| yön değiştir | REVERSE | REV | Reverse the direction of LINEs and PLINEs | REVERSE |
| aç/kapat | PEDIT | PE | CLOSE / OPEN / VERTEX index X,Y; no curve/spline editing | PEDIT CLOSE |
| dairesel dizi | ARRAYPOLAR | AP | Independent copies in a circle; not an associative array | ARRAYPOLAR 0,0 8 360 |
| hizala | ALIGN | AL | 2D: move and rotate using source/target pairs; Yes scales, No keeps the size | ALIGN 0,0 200,200 1000,0 200,1200 N |
| taşı | MOVE | M | Move the selection by a relative offset; wall joins are kept | MOVE @0,200 |
| kopyala | COPY | CO | Copy the selection together with its attached openings | COPY @1000,0 |
| döndür | ROTATE | RO | Rotate by an angle in degrees about a base point | ROTATE 0,0 45 |
| ölçekle | SCALE | SC | Scale uniformly from a base point | SCALE 0,0 1.5 |
| aynala | MIRROR | MI | Mirrors the selection; the default H (No) keeps the sources, E (Yes) erases them | MIRROR 0,0 0,1000 H |
| ofset | OFFSET | O | Offset to the left for lines/walls; outward for a closed convex boundary | OFFSET 200 |
| buda, budama, kırp | TRIM | TR | In quick mode, trim only the clicked segment of a polyline; B for selected boundaries, Shift to extend temporarily | TRIM 12,15 250,0 |
| uzat | EXTEND | EX | Extend the clicked end of the selected line, open polyline or arc to the nearest boundary | EXTEND 12,15 250,0 |
| yuvarlat | FILLET | F | Corner with a tangent arc between two selected lines | FILLET 200 |
| pah | CHAMFER | CHA | Equal-distance chamfer between two selected lines | CHAMFER 200 |
| birleştir | JOIN | J | Join end-to-end lines into a single polyline | JOIN |
| parçala | EXPLODE | X | Break a polyline/hatch boundary into lines | EXPLODE |
| dizi | ARRAY | AR | Rows, columns, X spacing, Y spacing | ARRAY 3 4 1500 2000 |
| çizim sırası | DRAWORDER | DORDER | Move the selected 2D objects in the draw order with FRONT/BACK or ABOVE/BELOW targetId | DRAWORDER FRONT |
| sil | ERASE | E | Delete the selection and dependent objects | ERASE |
| — | UNDO | U | Undo the last action | UNDO |
| — | REDO | — | Redo the undone action | REDO |
| — | COPYCLIP | — | Copy the selected CAD objects to the clipboard | COPYCLIP |
| — | COPYBASE | — | Copy to the clipboard with a base point | COPYBASE |
| — | CUTCLIP | — | Cut the selected CAD objects to the clipboard | CUTCLIP |
| — | PASTECLIP | — | Paste CAD objects from the clipboard at a specified point | PASTECLIP |
| — | PASTEORIG | — | Paste CAD objects from the clipboard at their original coordinates | PASTEORIG |
Layers, selection and properties
| Turkish | Command | Alias | What it does | Example |
|---|---|---|---|---|
| özellik eşle | MATCHPROP | MA | Apply the source object's layer, colour and lineweight to the selection | MATCHPROP 3 |
| katman ayır | LAYISO | — | Hide layers outside the selection; the previous visibility is kept in the history | LAYISO |
| tümünü göster | LAYON | — | Make all layers visible | LAYON |
| boş katman sil | PURGE | PU | Delete only unused layers other than 0 | PURGE |
| hızlı seçim | QSELECT | QS | Dialog for selecting by type and layer | QSELECT |
| katman, katman özellikleri | LAYER | LA | Create a layer; the current layer is chosen in the interface | LAYER Wall |
| renk | COLOR | COL | Change the colour of the selected objects or of new objects; BYLAYER follows the layer | COLOR #22D3C5 |
| çizgi kalınlığı | LINEWEIGHT | LW | Change the lineweight in mm of the selected objects or of new objects | LINEWEIGHT 0.35 |
| — | LINETYPE | LT | Change the linetype of the selected objects or of new objects; BYLAYER follows the layer | LINETYPE DASHED |
| tümünü seç | SELECT | SEL | Select visible, unlocked objects; example of selecting by ID: SELECT 3 7 | SELECT ALL |
| — | LWDISPLAY | LWT | Show or hide lineweights on screen; saved lineweights and output are unchanged. | LWDISPLAY ON |
| özellikler | PROPERTIES | PR | Show the properties of the selected object | PROPERTIES |
| — | SELECTALL | — | Select visible unlocked objects | SELECTALL |
Blocks and groups
| Turkish | Command | Alias | What it does | Example |
|---|---|---|---|---|
| grup | GROUP | G | Combine the selection into a persistent selection group | GROUP Facade |
| grubu dağıt | UNGROUP | UG | Dissolve the selected groups; the geometry is kept | UNGROUP |
| blok oluştur | BLOCK | B | Store the selected simple 2D objects as a reusable named definition relative to a base point; the sources are kept | BLOCK Armchair 0,0 |
| — | BLOCKUPDATE | BU | Update the definition and its linked INSERT placements together from the selected 2D source | BLOCKUPDATE Armchair 0,0 |
| blok ekle | INSERT | I | Insert a placement linked to a named 2D definition; point, uniform scale and angle in degrees | INSERT Armchair 3000,2000 1 0 |
View and drawing aids
| Turkish | Command | Alias | What it does | Example |
|---|---|---|---|---|
| kaydır | PAN | P | Pan the view with the mouse | PAN |
| açı izle | POLAR | — | Snap to nearby angles in 15-degree increments — F10 | POLAR |
| dinamik giriş | DYNAMIC | — | Dynamic distance at the cursor — F12 | DYNAMIC |
| ekrana sığdır | ZOOM | Z | Fit the drawing to the screen; short form: ZE | ZOOM EXTENTS |
| ızgara | GRID | — | Turn the grid on/off — F7 | GRID |
| dik çizim | ORTHO | — | Orthogonal direction lock — F8 | ORTHO |
| ızgaraya yakala | SNAP | — | Snap to grid — F9 | SNAP |
| nesne yakalama | OSNAP | — | Endpoint/midpoint/centre/intersection snaps — F3 | OSNAP |
| — | DSETTINGS | SNAPSETTINGS | Object snap settings with icons; select types individually, clear all, or turn off temporarily with F3 | DSETTINGS |
| — | UNITS | — | Working unit and number display precision | UNITS |
| — | OTRACK | — | Alignment tracking from snapped reference points — F11 | OTRACK |
File, output and help
| Turkish | Command | Alias | What it does | Example |
|---|---|---|---|---|
| komut ara | COMMANDS | CMD | Searchable command catalogue | COMMANDS |
| kaydet | SAVE | QSAVE | Save the local project | SAVE |
| — | OPEN | — | Open a local project or a supported subset of DXF | OPEN |
| — | NEW | — | New blank drawing | NEW |
| örnek daire | DEMO | — | Open the sample flat as a new document | DEMO |
| — | PUBLISH | — | Publish the selected sheets as a multi-page PDF or as confirmed printer output | PUBLISH |
| — | HELP | ? | Command reference — F1 | HELP |
| farklı kaydet | SAVEAS | — | Save the project to a separate file | SAVEAS |
| sayfa ayarı | PAGESETUP | — | Open page and print settings | PAGESETUP |
| baskı önizleme | PLOTPREVIEW | — | Open the print preview | PLOTPREVIEW |
| PDF aktar | PDF | — | Export to PDF | PDF |
| DXF aktar | DXF | — | Export to DXF | DXF |
| SVG aktar | SVG | — | Export to SVG | SVG |
| PNG aktar | PNG | — | Export the view to PNG | PNG |
| yazdır | PRINT | PLOT | Open the print dialog | PRINT |
If you use AutoCAD
Most command names and aliases are in a form that AutoCAD users will find familiar (such as LINE / L, TRIM / TR, OFFSET / O). However, ARCTE CAD is an independent product; the behaviour and options of the commands may not be exactly the same. AutoLISP programs and AutoCAD add-ons do not work.
AutoCAD is a registered trademark of Autodesk, Inc. ARCTE CAD has no connection with Autodesk.
Frequently asked questions
Both work. Turkish names (duvar, buda, ekrana sığdır), English names (WALL, TRIM, ZOOM EXTENTS) and aliases (W, TR, ZE) run the same command.
No. The command line converts Turkish characters; cizgi and çizgi, or olcekle and ölçekle, are the same command.
Open the command reference with the F1 key, or type komut ara (COMMANDS) to use the searchable command catalogue.
Most command names and aliases are familiar, but the behaviour is not exactly the same. AutoLISP programs and AutoCAD add-ons do not work.